Search Results

The prototype solid particle counting system (SPCS) has been used to study solid particle emission from gasoline and diesel vehicles. As recommended by the PMP draft proposal, exhaust is diluted by a Constant Volume Sampler (CVS). The SPCS takes the sample from the CVS tunnel. Transient test cycles such as EPA FTP 75, EPA HWFET (EPA Highway Fuel Economy Cycle), and NEDC (New European Driving Cycle) were tested. The repeatability of the instrument was evaluated on the diesel vehicle for three continuous days. The instrument exhibits good repeatability. The differences for the EPA ftp 75, the EPA HWFET, and the NEDC in three continuous tests are ± 3.5%. The instrument is very sensitive as well and detects the driving differences. A large number of solid particles are found during the hard acceleration from both the gasoline and the diesel vehicles. Solid particle emissions decrease quickly at deceleration and when vehicles approach constant speed.

A prototype solid particle counting system (SPCS) has been developed in Horiba. It measures the engine exhaust solid particle number emissions in real-time. The instrument is designed to follow the recommendation in the PMP proposal for solid particle number emissions measurement on Light-duty diesel vehicles. Two wide range continuous diluters, which were developed during this project, have been used as cold and hot diluters, respectively. The accuracy of the dilution ratio is normally ± 4% for the designed range. The instrument has low particle losses, and exhibits over 95% penetration for solid particles. The new instrument has functions such as, normal measurement, dilution ratio control, daily calibration for condensation particle counter (CPC), etc. These functions have been automated to make the instrument's operation simple.

Measurements of soot and SOF emitting from automobile engines by conventional gravimetric method and soxhlet extraction method are difficult and time-consuming processes. The composition in the filter substrate may change during time-consuming analysis. Therefore an accurate and real time measurement method for particulate matter is the key demand for automobile industry. This paper describes a new concept for analyzing PM, which includes measurement of soot and SOF separately, as well as the total PM emission from automobile engine continuously. The concept comprises of the real-time measurement of soot emission with a diffusion charger (DC) combined with a specific dilution system. A differential flame ionization detector with separate sample line temperatures (47°C and 191°C), have been applied for the SOF measurement. The total PM is then expressed as the sum of soot and SOF mass.

In response to the appearance of formal regulations, CFR part 1065 subpart J, a new in-use emission measurement system was developed, the OBS 2000. The OBS 2200 uses partial-vacuum analyzers. The heated flame ionization detector (HFID), heated chemiluminescence detector (HCLD) and heated non-dispersive infrared analyzer (HNDIR) are all upstream of the sample pump. This design decreases the response time of the analyzers, lowers power consumption and minimizes the overall dimensions of the system by avoiding the use of a heated sample pump. The size of the heated zones is also minimized to reduce power usage. Typical power consumption of analyzer unit is less than 500 W. The overall dimension of the main unit is 350mm (W) × 330mm (H) × 500mm (D). Analyzer linearity checks as required by new regulations [1] for all available ranges will be presented along with cut point accuracies relative to full scale and percentage of point.

The purpose of this study is to improve low-temperature flow-properties of biodiesel fuels (BDF) by blending with ethanol and to analyze the combustion characteristics in a diesel engine fueled with BDF/ethanol blended fuel. Because ethanol has a lower solidifying temperature, higher oxygen content, lower cetane number, and higher volatility than BDF, ethanol blending would have a large effect on cold flow performance, mixture formation, ignition, combustion, and exhaust emissions. The engine experiments in the study were performed with a diesel engine and blends of BDF and ethanol at different blending ratios. The cold flow performance of the blended fuels was evaluated by determining the fuel cloud point. The experimental results show that the ethanol blending lowers the cloud point of the blended fuel and significantly reduces smoke emissions from the engine without deteriorating other emissions or thermal efficiency.

Homogeneous Charge Compression Ignition (HCCI) is effective for the simultaneous reduction of soot and NOx emissions in diesel engine. In general, high octane number fuels (gasoline components or gaseous fuels) are used for HCCI operation, because these fuels briefly form lean homogeneous mixture because of long ignition delay and high volatility. However, it is necessary to improve injection systems, when these high octane number fuels are used in diesel engine. In addition, the difficulty of controlling auto-ignition timing must be resolved. On the other hand, HCCI using diesel fuel (diesel HCCI) also needs ignition control, because diesel fuel which has a low octane number causes the early ignition before TDC. The purpose of this study is the ignition and combustion control of diesel HCCI. The effects of parameters (injection timing, injection pressure, internal/external EGR, boost pressure, and variable valve timing (VVT)) on the ignition timing of diesel HCCI were investigated.

Conditioning of diluted exhaust gas by Thermo-Conditioner prior to measurement has been proposed by the GRPE/PMP Research Council of the United Nation in order to achieve stability in nano-particle measurement. In this study the effect of thermo-conditioner on the thermo-physical behavior of nano-particle under different conditions have been clarified. Stability in measurement was also attempted depending on the characteristics of nano-particles. Quality of the raw exhaust gas, the dilution ratio and temperature, and the thermal conditioning temperature were considered as the main parameters. Exhaust gas from a medium duty DI diesel engine was used for analysis. Scanning Mobility Particle Sizer was used for measuring the concentration of nano-particles. It was concluded that the concentration of nuclei-mode particles within the size range of 15∼30 nm are significantly influenced by the thermal conditioning temperature.

In addition to PM total matter, PM size distribution is recently receiving increased attention because of the dependency of PM size on human health effects. Thus, PM size distributions and the emission behavior under various driving patterns are becoming important in diesel particulate emissions. Electrical Low Pressure Impactor (ELPI)_is a candidate to measure continuously, not only PM mass, but also particulate size distribution. Therefore, we investigated using ELPI to measure diesel particulate mass and size distribution, together with time series behaviors under various driving patterns. This study demonstrated the feasibility of continuous measurement of PM size distribution by means of an ELPI. The typical PM size distribution curve on weight base has a peak of 0.18 micrometer. The typical PM size distribution curve on number base has a peak of 0.11 micrometer. Engine load influences these characteristics.

This research investigates engine performance and the possibility of reducing exhaust emissions by using Dimethyl Ether (DME). There are high expectations for DME as a new alternative fuel for diesel engines for heavy-duty vehicles. In this experiment, a single cylinder direct-injection diesel engine with displacement of 1.05 liter and a compression ratio of 18:1 was used as a base engine. Common rail type DME fuel injection equipment for the single cylinder engine experiment was installed, and direct injection in the cylinder of DME was tried. Results indicated that high injection pressure, high swirl ratio, and supercharging using multi-hole injectors are effective for combustion promotion in the DME fueled diesel engine (DME engine). The output of the DME engine using supercharging with an intercooler and EGR was higher than that of a diesel engine. By increasing the EGR rate Nox emission was reduced to about 1/3 that of the diesel engine. Smoke was not completely emitted.

Direct injection natural gas engines need to produce in the mixing process between the fuel jet and the air in the cylinder a “stratified” fuel-air mixture, with an easily ignitable composition near the spark plug at the time of ignition. Stratified-charge engines have a tendency to produce high NOx emissions due to the high temperature of burning areas at the start of combustion since the fuel-air mixture is not uniform. Therefore, it is necessary to reduce NOx emissions from direct injection natural gas engines. The objective of this study is to investigate measures to reduce emissions, especially NOx emissions, from direct injection natural gas engines. A single cylinder test engine was equipped with a newly developed high-pressure electromagnetic injector and a spark plug.

Numerical models of three kinds of mass emission measurement systems, i.e. the constant volume sampler (CVS) system, the mini-diluter system and the direct modal-mass measurement system have been built on PC using a software called Mathematica®. The models are capable of simulating gas compounds concentration in the CVS bags and mass emitted during a test, using the time trend exhaust emission patterns, the exhaust gas flow rate pattern, and initial setting values like dilution ratio. Major error factors in the measurement systems, such as H2O condensation, gas compounds present in ambient air, delay and smoothing of the gas stream, and performance of the analyzers, can also be introduced to the calculation. Using the models, various techniques to optimize the sampling system are quantitatively compared.

The subject of engine emissions is expected to be at the forefront of environmental regulations and consumers’ concerns for years to come. As technology develops to comply with new and different requirements in various regions of the world, understanding the fundamental principles of how engine emissions occur, and how they can be properly measured, is vitally important. Engine Emissions Measurement Handbook, developed and co-authored by HORIBA Automotive Test Systems team addresses the main aspects of this subject. Written with the technical user in mind, this title is a must-have for those involved in engine development and testing, and environmental researchers focusing on better ways to minimize emissions pollution.